LM-2 Aluminium Sheet

EN AC 46100 Sheet is an aluminum alloy formulated for casting. Aluminium LM2 Sheet is typically furnished in the as-fabricated (no temper or treatment) condition. EN 1706 Aluminium Sheet is a little difficult to machine since the high silicon content causes rapid tool wear. It is, however, far easier than the LM6 and LM20 alloys as the tendency to drag is practically eliminated by the presence of copper and other elements. Resistance to corrosion by ordinary atmospheric conditions is good and by marine atmosphere fairly good. ASTM B209 LM2 Aluminium Sheet is inferior in this respect to LM6 but can be improved by anodic treatment.

LM2 Sheet can be anodically treated to give a protective surface of a darkish grey colour The surfaces of die-castings. however, are not generally suitable for decorative anodising. This alloy conforms to BS 1490:1988 LM2.

LM-2 Aluminium Sheet Temper 0, H32, H34, H38 as per ASTM B209, ASTM-B-209, EN573, and EN485 international standards. Aluminium Casting Alloy (AL – Si10Cu2Fe), EN 1706 AC-46100, LM2 (EN 1706 AC-46100) – Aluminium Casting Alloy

Sasa Aluminium is the leading manufacturer and exporter of LM-2 Aluminium Sheet. Supplier of ASTM B209 LM-2 Aluminium Sheet from 0.5mm to 5mm Thick 1000mm x 1000mm to 2500mm x 1250mm Tempers manufactured in accordance with international standards ASTM B209, ASTM-B-209, EN573, and EN485, check LM-2 Aluminium Sheet price. The general widths of LM-2 H16 Aluminum sheets are 1000mm, 1250mm and 1500mm, while common lengths are 2000mm, 2500 mm and 3000mm respectively. Wholesale Trader of LM-2 Commercial Aluminium Sheet offered by Sasa Aluminium , China. Stockist of LM-2 Aluminium Sheet, H32 LM-2 Aluminium Stucco Sheet, H38 Commercial LM-2 Aluminium Sheet, ASME SB209 LM-2 Aluminium Patterned Sheet, LM-2 Aluminium Embossed Sheet, LM-2 Aluminium Extruded Sheet, LM-2 Aluminium Sheet and LM-2 Aluminium Sheet in China.

Standard Dimensions of LM-2 Aluminium Sheet

Standard dimensions (a x b) of Aluminium LM-2 Sheet

Aluminium LM-2 Sheet up to 9.9 mm
2.000 x 1.000 mm
2.500 x 1.250 mm
3.000 x 1.500 mm

Oversize Aluminium LM-2 Sheet
4.000 x 2.000 mm
6.000 x 2.500 mm
8.000 x 2.500 mm

Other dimensions on request

LM-2 Aluminium Sheet Products Show:

Aluminium LM-2 Sheets Manufacturer in China:

1100-H14 Aluminum Sheet:  ASTM-B-209
2024-T3 ALCLAD Aluminum Sheet:  AMS-QQ-A-205/5, ASTM-B-209, AMS-4041
2024-T3 BARE Aluminum Sheet:  AMS-QQ-A-205/5, ASTM-B-209, AMS-4037
2219-T6 Aluminum Sheet:
2219-O Aluminum Sheet:  AMS-QQ-A-250/30
3003-H14 Aluminum Sheet:  ASTM-B-209
3003-O Aluminum Sheet:  ASTM-B-209
4047-F Aluminum Sheet:  AMS-4185, BAlSi-4
5052-H32 Aluminum Sheet:  ASTM-B-209, AMS-4016
5052-H38 Aluminum Sheet:  ASTM-B-209
5052-O Aluminum Sheet:  ASTM-B-209, AMS-4015
6061-O Aluminum Sheet:  ASTM-B-209, AMS-4025
6061-T4 Aluminum Sheet:  ASTM-B-209, AMS-4026
6061-T6 Aluminum Sheet:  ASTM-B-209, AMS 4027
7075-T6 Aluminum Sheet:  AMS-QQ-A-250/12, AMS-4045
7075-O ALCLAD Aluminum Sheet:  ASTM-B-209
7075-O BARE Aluminum Sheet:  AMS-QQ-A-250/12, AMS-4045
Aluminum Specular Lighting Sheet

Please note: Other alloys available upon request
* Special Tolerances Available
* Polishing & PVC Protected

Standard Specification of LM-2 Aluminium Sheet

Standards and specifications by country

LM-2 Aluminium Sheet Sizes

LM-2 Aluminium Sheet Weight Chart

Width: 1.000 mm | Length: 2.000 mm

LM-2 Aluminium Sheet Chemical Composition

Aluminium LM-2 Sheet Mechanical Properties

LM2-M

The values shown are typical ranges for chill cast test bars produced to the requirement of B.S. 1490. Die cast values obtained on 6mm test bars. Those in heavier type are minimum specification values.

For most applications LM2 and LM24 are interchangeable, but LM2 has a slightly lower density, LM6 and LM20 would be betterthan LM2 in a corrosive environment, unless it can be protected by anodizing. LM2 has poor weldability and poor brazeability.

Aluminum Alloy Heat Treatment Temper Designations

Basic Aluminum Heat Treatment Designations

• F As Fabricated
• O Annealed
• H Strain Hardened
• W Solution Heat Treated
• T Solution Heat Treated

Heat Treating T Temper Codes

• T1 – Cooled from an elevated temperature shaping process and naturally aged to a substantially stable condition.
• T2 – Cooled from an elevated temperature shaping process, cold worked, and naturally aged to a substantially stable condition.
• T3 – Solution heat treated, cold worked, and naturally aged to a substantially stable condition.
• T4 – Solution heat treated, and naturally aged to a substantially stable condition.
• T5 – Cooled from an elevated temperature shaping process then artificially aged.
• T6 – Solution heat treated then artificially aged.
• T7 – Solution heat treated then overaged/stabilized.
• T8 – Solution heat treated, cold worked, then artificially aged.
• T9 – Solution heat treated, artificially aged, then cold worked.
• T10 – Cooled from an elevated temperature shaping process, cold worked, then artificially aged.

Additional digits may be used after the first T temper digit to indicate subsequent stress relieving by processes such as stretching, compressing, or a combination.

H Temper Strain Hardening Codes

• H1 – Strain hardened only
• H2 – Strain hardened and partially annealed
• H3 – Strain hardened and stabilized
• H4 – Strain hardened and lacquered or painted. This assumes that thermal affects from the coating process affect the strain hardening; seldom encountered.

LM-2 Packing Information of Aluminum plate :

Application of LM-2 Aluminium Sheet

LM-2 Aluminium Sheet is the most widely used form of Industrial Aluminium. LM-2 Aluminium Sheets find applications in various industries such as manufacturing cans and packages, transportation, home appliances, building and construction.

LM-2 Aluminium Sheet Applications